Reverse Mixer Machine Controller

It has 64 KB EEPROM for data & parameter storage

• Operating Supply: 110-230VAC / 24-12 VDC
• Keyboard: Eight keys membrane like Keypad
• Display: LCD with Back Light (for each channel)
• Input: Load cell Sensor (Up to Four channel)
• Excitation Voltage: 10VDC
• Onboard RTC

Field Programmable parameters:

• Set points for four components, Water and Additive
• Offset for four components
• Minimum weight to start new batch
• Number of batches, Date, Time
• Delay time
• Scale factor: Number of pulse per Liter for water

Control Outputs: Total 5 relay outputs:

• Four relays to control Feeding of components
• One relay to control water feeding
• One relay to Control Additive Feeding
• Digital Inputs: 2 digital inputs (One for water metering & one for remote command
• Calibration: Offset & Span calibration through software using keypad
• Report: Batch wise online
• Serial Interface: RS-232/RS-485 (for Printer/Computer/HMI/Pen drive module)
• USB Port for PEN Drive

Mechanical Data: Mounting: Panel mounting

• Cutout size: 138 mm x 138 mm
• Outer dimension: 144mm(W) x144mm (H) x125mm (Depth)
• Enclosure: Metallic, Powder coated, General Purpose

Micro controller based unit

It has 64 KB EEPROM for data & parameter storage

Operating Supply: 110-230VAC

Keyboard: Eight keys membrane like Keypad

Display: 4 digit LED (for each channel)

Input: Load cell Sensor (Up to Four channel)

Excitation Voltage: 10VDC

Number of components: Up to 4 

Discharge sequence Programmable

Onboard RTC

Field Programmable parameters:

- Set points for four components

- Offset for four components

- Minimum weight to start new batch

- Gate Time: delay time between feeding of the four components

- Dead Weight: Minimum to start a new batch

- Control Outputs: Total 4 relay outputs:

Four relays to control Feeding of components

Digital Inputs: 2 digital inputs (One for water metering & one for remote command)

Calibration: Offset & Span calibration through software using keypad

Serial Interface: 

- RS-232/RS-485 (for Printer/Computer/HMI/Pen drive module)

Mechanical Data: Mounting: Panel mounting

- Cutout size: 138 mm x 138 mm

- Outerdimension:144mm(W)x144mm(H)x125mm (Depth)

Enclosure: Metallic, Powder coated, General Purpose

It has 64 KB EEPROM for data & parameter storage
Operating Supply: 110-230VAC
Keyboard: Six keys membrane like Keypad
Display: 4 digit LED
Input: Load cell Sensor (Single channel)
Excitation Voltage: 10VDC
Field Programmable parameters:
Set points for component
Control Outputs: Total 1 relay outputs:
1 relay to control Feeding of components
Calibration:  Span calibration through software using keypad
Mechanical Data: Mounting: Panel mounting
Cutout size: 138 mm x 138 mm
Outer dimension: 144mm(W) x144mm (H) x125mm (Depth)
Enclosure: Metallic, Powder coated, General Purpose

Power Supply: 110-230VAC / 24 VDC

Display: Dual 4-Digit, 0.34” 7-Sgement Red LED

Key board: Four keys membrane like

Input: Pulse Input from Proximity/Water meter / Analog input

Output : MODBUS RS232/RS485

Calibration: Through keypad

Set point:  Water to be dispensed

Enclosure: DIN standard Panel Mounting, Plastic, General Purpose 

Dimension: 

- Outer: 72 mm (W) x 72 mm (H) x (D) 110 mm 

- Cut-out: 66 mm x 66 mm

We are distributing a wide gamut of Loss In Weight Controller. It is manufactured under the observation of adroit personnel and innovative techniques. This controller is operated in a digital and upgraded tools. It is used to balance the weight and easy to shut down when it requires. Loss In Weight Controller is able to measure the rate of discharge of required material. It is resistant to heat and water. It is convenient to regulate the mass flows.