SAMYAK INSTRUMENTATION PVT LTD

Call us: +919925671900

trusted seller

Process Indicator

The offered Process Indicator is made available by us for use in the various commercial and industrial applications. These are indicators which directly measure the performance of key processes that affect customer expectations. Specific actions can be taken to improve the performance of these indicators, which in turn should improve the performance of the result measurable. These indicators are particularly useful in reviews focused on improvement. Where the outcome indicators suggest performance is below the level expected, process indicators can be used diagnostically to explore the reasons. The offered Process Indicator is very accurate and effective.

Process Indicator SMIT 302

Accepts Analog Input: 4-20 mA, 0-10 VDC, 0-5VDC

Four Keys Membrane Like Keypad 

Display: 4-Digit Numeric 0.8 Red LED display for Process Variable

Operating: 24 VDC / 100-263 VAC

Transmitter Power supply: +24VDC / 50mA

Programmable parameters: Zero, Full scale, Decimal position 

Non-volatile Memory for storing configuration parameters

Calibration thro software


Options:

- Retransmission: 4 -20 mA / 0-10 VDC Isolated (Linear Proportional to Indication)

- Two Relays (5A/230VAC) for Alarm

- Communication: RS232 or RS-485 (2-wire), MODBUS protocol 


Mechanical Data: Mounting: Panel mounting

- Cutout size: 92 mm x 96 mm

- Outer dimension: 96 mm x 96 mm x 120 mm (Depth)

Enclosure: Normal

Process Indicator SMIT 301H

Accepts Analog Input: 4-20 mA, 0-10 VDC, 0-5VDC

Four Keys Membrane Like Keypad

Display: 4-Digit Numeric 0.56 inch Red LED display for Process Variable

Operating: 24 VDC / 100-263VAC

Transmitter Power supply: +24VDC/50mA

Programmable parameters: Zero, Full scale, Decimal position 

Non-volatile Memory for storing configuration parameters

Calibration thro' software


Options:

- Retransmission: 4 -20 mA / 0-10 VDC Isolated (Linear Proportional to Indication)

- Two Relays (5A/230VAC) for Alarm

- Communication: RS232 or RS-485 (2-wire), MODBUS protocol


Mechanical Data: 

Mounting: Panel mounting

- Cutout size: 92 mm x 44 mm

- Outer dimension: 96 mm x 48 mm x 120 mm (Depth)

Enclosure: Normal

Process Indicator Controller

MICRO CONTROLLER BASED 

  • Accepts Analog Input: 4-20 mA, 0-10 VDC, 0-5 VDC
  • Four Keys Membrane Like Keypad 
  • Display: 4-Digit Numeric 0.56 Red LED 
  • Operating: 24 VDC / 100-263VAC
  • Transmitter Power supply: +24VDC/50mA
  • Programmable parameters: Zero, Full scale, Decimal position 
  • Non-volatile Memory for storing configuration parameters
  • Calibration thro software

Options:

  •  Retransmission: 4 -20 mA / 0-10 VDC Isolated (Linear Proportional to Indication)
  •  Two Relays (5A/230VAC) for Alarm
  •  Communication: RS232 or RS-485 (2-wire), MODBUS protocol 
  • Mechanical Data: Mounting: Panel mounting
  •  Cutout size: 92 mm x 92 mm
  •   Outer dimension: 96 mm x 96 mm x 120 mm (Depth)
  • Enclosure: Normal

Flow Rate Indicator Totaliser

Analog Input: 4.0-20.0mA/0-20mA/0-5V/1-5V (factory set)

Pulse Input: OC type, Source, Sink, Potential Free

Operating Supply:110-230 VAC +/-10% or 24VDC

Transmitter Power Supply: +24V DC +/- 5%, 50 mA


Field Programmable parameters:

Zero, Full scale, Decimal position, Time Base for Totaliser, Set points for Alarm/Batching, K-Factor

K-Factor settable in the range of x.xxxxx to xxxxxx

Reset Totaliser: Through KB (Password Protected)

Full Scale range: 0 to 999999

Default display: Selectable between Flow rate & Totaliser

Display: Six Digit 0.56" 7-Segment Red LED

All parameters/Settings are stored in serial EEPROM.

Calibration: Through software using keypad


Options:

- Serial Interface: RS-232/RS-485 (MODBUS)

- Retransmission: 4.0 to 20.0 mA Isolated Proportional to Indication

- Relays: Two, Rating: 2.0A/230VAC

- FP enclosure


Mechanical Data: Mounting: Panel mounting

- Cutout size: 92 mm (W) x 44 (H) mm

- Outer dimension: 96 mm (W) x 48 mm (H) x 130 mm (D)

Enclosure: Plastic, General Purpose Panel Mounting Type

Process Indicator

Input: Pulse Input from Proximity / Water meter / Analog input (0-10 VDc / 4-20 mA)

Power Supply: 110-230 VAC / 24 VDC

Display: Dual 4-Digit, 0.34 7-Sgement Red LED

Key board: Four keys membrane like

Interface: MODBUS RS232/RS485

Parameter Setting: Through keypad

Enclosure: DIN standard Panel Mounting, Plastic, General Purpose 


Dimension: 

- Outer: 72 mm (W) x 72 mm (H) x (D) 110 mm 

- Cut-out: 66 mm x 66 mm

Process Indicator Controller (5 Digits)

MICROCONTROLLER BASED 

ACCEPTS ANALOG INPUT: 4-20 MA, 0-20 MA, 0-5 V, 1-5 V

NUMBER OF INPUTS CHANNELS: UP TO 4

DISPLAY RESOLUTION: 4 DIGITs

KEYPAD : FOUR KEYS MEMBRANE LIKE 

DISPLAY : 5-DIGIT, 7-SEGMENT, 0.56 inch RED LED DISPLAY 

OPERATING AT 100-263VAC

TRANSMITTER POWER SUPPLY: +24VDC/50MA

PROGRAMMABLE PARAMETERS: ZERO, FULL SCALE, DECIMAL POSITION 

NON-VOLATILE MEMORY FOR STORING CONFIGURATION PARAMETERS

FIELD CALIBRATION THRO' KEYPAD

OPTIONS:

- Retransmission: 4.0-20.0mA Isolated (Linear Proportional to Indication)

- Two Relays (5A/230VAC) for Alarm

- Communication: RS232 or RS-485 (2-wire), MODBUS protocol 


Mechanical Data: Mounting: Panel mounting

- Cutout size: 92 mm x 92 mm

- Outer dimension: 96 mm x 96 mm x 110 mm (Depth)

Enclosure: General Purpose Plastic

Process Indicator DPIT 12

MICROCONTROLLER BASED

Accepts Analog Input: 0/4.0-20.0m, 0/1-5 V, Pulse Input

Four Keys membrane Like Keypad

8-Digit Numeric 0.30” Red LED display for Process Variable & Set Point

Operating at 100-263VAC/24VDC

Transmitter Power supply: +24VDC/50mA

Programmable parameters: Zero, Full scale, Decimal position etc..

Non-volatile Memory for storing configuration parameters

Input & Output calibration thro’ software


Options:

- Analog Output: two Channels: 4.0-20.0mA Isolated (Linear Proportional to Indication)

- Two Relays (2A/230VAC) for Alarm

- Communication:RS232 or RS-485 (2-wire), MODBUS protocol


Mechanical Data: Mounting: DIN rail/Wall mounting

- Outer dimension: 70 mm(W) x 75 mm(H) x 110 mm(D)

- Enclosure: Normal


Application:

- Field mountable isolator: single channel or dual channel

- Process Indicator

- Analog to serial converter

- Alarm generator

X


Back to top